1cm LED RGB+CCT STRIP, 20W/m (100W/5m) 24V HIGH CRI98
High quality 20W 24V RGB + CCT led strip!
This led strip uses RGB circuit with the CCT (2500-6000K) HIGH CRI around 98 with (White colour). The led strip is dimmable. As a tape, it uses 3M tape that is extra durable and attaches the strip firmly. Led strip 20W (10W RGB +10W CCT) /meter is outputting enought for indirect moodlighting!
High quality 20W 24V RGB + CCT led strip!
This led strip uses RGB circuit with the CCT (2500-6000K) HIGH CRI around 98 with (White colour). The led strip is dimmable. As a tape, it uses 3M tape that is extra durable and attaches the strip firmly. Led strip 20W (10W RGB +10W CCT) /meter is outputting enought for indirect moodlighting!
Lighting
The strip is controlled with our VaLO Zigbee series remote (or HUE, Conbee2 USB ) and Zigbee RGB+CCT receiver. With these you can adjust freely RGB or CCT. The product can be seen at our showroom in Vantaa Koivuhaka.
This strip is mostly used in indirect lighting and for creating different moods. Perfect for spas, bars and terraces, also we have noticed that kids love this led strip. RGB led strip has 10W/m and has 50 RGB and 50 CCT led circuits on a meter. This makes the light pretty even, if installed in a way you cannot see the light source ie. indirect light. When installed on an aluminium profile, there are visible dots to be seen if looked straight to the light (or if installed next to a shiny wall).
Installation
LED strip comes in a 5m roll that can be cut to measure in every 12,5cm. We recommend that you solder the wanted lengths together as we have noticed that the fast clips tend to loosen after a few years and then the light starts flickering. There are 10 cm of mounting cable soldered to both ends of the strip. We will help you with any installation questions.
If you have more than 10m of RGB+CCT led strip, you need to feed the power from both ends to minimize the powerloss. All installations should be made on top of aluminium (ie. aluminium profile), that way the excess heat gets conducted away from led circuit and makes it last longer. Strip is 12mm wide, with thick copper base.
LED strip works well with solar power and in boats and cars, as it is 24VDC you might not even need a driver, just controller!
Remember to order a 24V driver and controller. For the whole 5 meters you need a minimum of 100W driver.
Dimming
LedStore's RGB+CCT led strip requires at least 40A Zigbee controller and HUB/remote. This is a perfect solution also in places where you have power for the strip but no wall switch ready. With this system, you just hook the wireless receiver between led strip and driver and have the remote wherever you like.
Create a light of your own
Why would you use led strip only in traditional way (cabinets, indirect light etc.) when you can make a light of almost anything. Old cart wheel, zinc bucket or even a wooden boat turns in to a light when you put led strip inside it! Get creative!
Light colour temperature
RGB (red, green and blue) and Warm (2500K) to cool white colour (6000K).
- Delivery status In Stock
- Brand Ledstore
- Breadcrumbs Home Led AreasLED interior lights 1cm LED RGB+CCT STRIP, 20W/m (100W/5m) 24V HIGH CRI98
- Category LED interior lights
- SKU 1cm-STRIP20-IP21-24V-RGBCCT
- Wattage 20
- Lumen 5000
- Designed in Finland No
- Voltage (V) 24
- Light control 176, 234
- Life span 35000
- Model 1cm STRIP20-IP21-24V-RGBCCT
- Size 12x2
- Length of the package 2.5
- Height of the package 25
- Width of the package 22
- Change 3M tape on backside
- Approval CE, RoHS, IP21
Be the first to write a review!
By rating you will be entered into a prize draw for a €50 gift voucher.
Zigbee CCT transformers
Zigbee CCT Products that you can use when you want stepless CCT control.
The luminaire is ordered without its own transformer and a group transformer is selected for CCT spots or CCT panels, as well as for CCT led strip lighting.
The transformer size for spots and panels is calculated by adding up the Watts + 25%.
For the CCT led strip, a 15% margin is sufficient.
e.g. 4x 9W CCT spot = 45W, so the closest is 50W
RF CCT transformers
RF CCT Products that you can use when you want stepless CCT control. The luminaire is ordered without its own transformer and a group transformer is selected for CCT spotlights or CCT panels, as well as for CCT led strip lighting.
The transformer size for spots and panels is calculated by adding up the Watts + 25%.
For the CCT led strip, a 15% margin is sufficient.
DALI2 (DT8) CCT transformers
DALI2 CCT Products you can use when you want stepless CCT control.
The luminaire is ordered without its own transformer and a group transformer is selected for CCT spots or CCT panels, as well as for CCT led strip lighting.
The transformer size for spots and panels is calculated by adding up the Watts + 25%.
For the CCT led strip, a 15% margin is sufficient.
e.g. 4x 9W CCT spot = 45W, so the closest is 50W
CCT wire harnesses
With our wiring harnesses you can quickly and reliably install CCT spots and CCT panels directly on one transformer. All luminaires are installed in parallel on the same transformer.
The spots come standard with a 15cm connecting cable with a connector, so you can easily create your own set with these wires.
with 3m spacer cables you can put even 2 in a row. All connection points have IP54 tight draught proofing.
In the distribution boxes (3 and 6) it is not mandatory to install a lamp on each connector.
WHAT IS CRI, THE COLOUR RENDERING INDEX
High quality LED lights also have a high colour rendering index, or CRI. A good colour rendering index (CRI) for home use is above 90, and nowadays many market lights are unfortunately closer to 80.
CRI tells you how well an LED light displays colours as they should be. For designers and architects, as well as interior designers, it should be one of the most important considerations. Make sure the lighting is perfect so that your artwork is what it is meant to be.
Colour rendering index
The colour rendering index is expressed as a number on a scale from zero to 100, where 0 = no colour rendering and 100 = full colour rendering. The colour rendering index of LED lights is also known as Ra, which is measured on a smaller scale than CRI. This Ra value does not include red tones or skin tones, for example, so it is a 'glossed' figure for the true quality of an LED light.
RA value
The Ra value measures the reproduction of colours using eight different reference colours. CRI takes into account the wider (15) wavelength range, including reds and other warm colours.
The Ra value is calculated by cutting the wavelength range, weighting the blue and violet tones, and calculating the weighted average of R numbers 1-8.
Excluded from the Ra value are, for example, the colour rendering of bright reds, yellows and greens, and shades close to skin tone. These are described by R-values between 9 and 15. The following is a picture of a measurement result that easily confuses the consumer.
This measurement is from a 9W CCT Led spot
Read more on this topic:
Colour rendering of LEDs - What is the difference between CRI and Ra-value?